Home / Concrete / Concrete Mix Design M20

Concrete Mix Design M20

Quick answer: Using IS 10262:2019 with OPC, 20 mm crushed aggregate, Zone II sand and a 100 mm slump, a typical M20 trial mix is cement 394 kg, water 197 kg, fine aggregate 672 kg and coarse aggregate 1,134 kg per m³, a ratio of about 1 : 1.71 : 2.88 at w/c 0.50. This is a starting point for trial mixes, not a final mix: your own materials and trials decide the final proportions.
M20 concrete mix design per cubic metre: cement 394 kg, water 197 kg, fine aggregate 672 kg, coarse aggregate 1134 kg, ratio 1 to 1.71 to 2.88

"Nominal mix" ratios like 1 : 1.5 : 3 ignore the actual cement, sand and stone you have. A designed mix starts from the strength you need and the materials on hand, and usually uses less cement for the same strength. This guide walks through the IS 10262:2019 method step by step for M20.

Design inputs

ParameterValue used
GradeM20 (fck = 20 N/mm²)
CementOPC 43 or 53 grade, specific gravity 3.15
ExposureMild (reinforced concrete), IS 456 Table 5
Coarse aggregate20 mm crushed angular, SG 2.74, saturated surface-dry (SSD)
Fine aggregateRiver or manufactured sand, Zone II, SG 2.65, SSD
Workability100 mm slump
AdmixtureNone (see note at the end)

Step 1: Target mean strength

IS 10262:2019 takes the higher of two values:

f′ck = fck + 1.65 s = 20 + 1.65 × 4.0 = 26.6 N/mm²
f′ck = fck + X = 20 + 5.5 = 25.5 N/mm²
Target mean strength = 26.6 N/mm²

The assumed standard deviation s = 4.0 N/mm² and X = 5.5 N/mm² for M20 are the code's defaults when you have no site data. With good records from your own plant, use your measured standard deviation instead.

Step 2: Water-cement ratio

From the strength–w/c relationship for your cement (IS 10262 Fig. 1, or better, your own curve), a target of 26.6 N/mm² needs a w/c of roughly 0.50 for typical OPC. IS 456 Table 5 limits w/c to 0.55 for mild exposure, so:

Adopt w/c = 0.50 (≤ 0.55 ✔)

Step 3: Water content

For 20 mm aggregate, the base water content is 186 kg/m³ for a 50 mm slump (IS 10262 Table 4). Add about 3% for every 25 mm of extra slump:

Slump 100 mm = 50 + 2 × 25 ⇒ +6%
Water = 186 × 1.06 = 197.2 kg/m³

Step 4: Cement content

Cement = 197.2 / 0.50 = 394 kg/m³
Minimum for mild exposure (IS 456 Table 5): 300 kg/m³ ✔   Maximum 450 kg/m³ ✔

Step 5: Coarse and fine aggregate split

For 20 mm aggregate with Zone II sand at w/c 0.50, the volume of coarse aggregate per unit volume of total aggregate is 0.62 (IS 10262 Table 5). For pumped concrete you may reduce this by up to 10%; this mix is not pumped.

Coarse aggregate fraction = 0.62    Fine aggregate fraction = 1 − 0.62 = 0.38

Step 6: Absolute volume calculation (per m³)

ItemCalculationVolume (m³)
Entrapped air (20 mm aggregate)1%0.0100
Cement394 / (3.15 × 1000)0.1252
Water197.2 / 10000.1972
All-in aggregate1 − 0.0100 − 0.1252 − 0.19720.6677
Coarse aggregate = 0.6677 × 0.62 × 2.74 × 1000 = 1,134 kg
Fine aggregate = 0.6677 × 0.38 × 2.65 × 1000 = 672 kg

Result: M20 trial mix per m³ (SSD aggregates)

CementWaterFine aggregateCoarse aggregatew/cRatio by weight
394 kg197 kg672 kg1,134 kg0.501 : 1.71 : 2.88

That is about 7.9 bags (50 kg) of cement per m³.

Step 7: Adjust for site moisture

The quantities above assume saturated surface-dry aggregates. On site, measure the moisture of your sand and stone and correct the batch weights: add the free water in the aggregates to the aggregate weight and subtract it from the mixing water (or add water if the aggregates are dry and absorptive).

Step 8: Trial mixes

Cast trial batches, check slump, and crush cubes at 7 and 28 days. If the strength or workability is off, adjust w/c or water content and re-run the volume calculation. Typical practice is three trials: the design w/c, and ±10% around it.

Why the mix still needs testing

  • Cement strength varies between brands and batches.
  • Aggregate shape and grading change water demand more than any table can predict.
  • Admixtures change everything: a water-reducer can cut water by 5–20%, which lets you reduce cement or w/c for the same slump.

FAQ

What is the nominal mix ratio for M20?

IS 456 allows a nominal mix of 1 : 1.5 : 3 for M20 (cl. 9.3). A designed mix like the one above usually performs better for the same cement.

How many bags of cement are in 1 m³ of M20?

About 7.9 bags (394 kg) in this designed mix. Nominal 1 : 1.5 : 3 mixes typically use 8 bags or more.

Can I use this mix for pumped concrete?

Pumped concrete usually needs more fines and a higher slump. Reduce the coarse aggregate fraction (for example to 0.56) and use a water-reducing admixture, then re-run the trial.

What if my exposure is moderate?

IS 456 Table 5 requires at least M25 for reinforced concrete in moderate exposure, so M20 is not allowed there.

References

  • IS 10262:2019, Concrete mix proportioning: guidelines (Bureau of Indian Standards).
  • IS 456:2000, Plain and reinforced concrete: code of practice, cl. 8 and Table 5.
  • IS 383:2016, Coarse and fine aggregate for concrete: specification.

Written by Engr. Abdul Latif, civil and structural engineer. Last reviewed: 16 November 2026. Proportions are a design starting point; confirm by trial mixes before use.