Home / Concrete / Development Length of Rebar

Development Length of Rebar

Quick answer: Development (anchorage) length is the length of bar that must be embedded in concrete so the bar can reach its design stress without pulling out. For a 16 mm bar in tension it works out to about 48φ (IS 456, M25, Fe500), 40φ (BS 8110, fcu 30, fy 500), 36φ (Eurocode 2, C30/37, good bond) and 38φ (ACI 318, 28 MPa, Grade 420). The four codes use different formulas, so never mix values between them.
Development length of rebar diagram: bar embedded in concrete with bond stress, and Ld for a 16 mm bar to IS 456, BS 8110, Eurocode 2 and ACI 318

Development length governs how far bars extend past supports, into columns and footings, and how long laps must be. All four major codes start from the same idea: the bond stress around the bar's surface must balance the force in the bar. They differ in how they set the bond stress and the safety factors.

The common principle

Force in bar = bond around the embedded length
(π φ² / 4) × σs = (π φ) × Ld × fb
⇒ Ld = φ σs / (4 fb)

where φ is the bar diameter, σs the design stress in the bar and fb the design bond stress. Each code below is a version of this equation.

IS 456:2000 (India)

Ld = φ × 0.87 fy / (4 τbd)   (cl. 26.2.1)

τbd is the design bond stress for plain bars in tension (cl. 26.2.1.1): 1.2 N/mm² for M20, 1.4 for M25, 1.5 for M30, 1.7 for M35 and 1.9 for M40 and above. For deformed bars (Fe415, Fe500) increase it by 60%, and for bars in compression by a further 25%.

ConcreteFe415, tensionFe500, tensionFe500, compression
M2047.0φ56.6φ45.3φ
M2540.3φ48.5φ38.8φ
M3037.6φ45.3φ36.2φ
M3533.2φ40.0φ32.0φ
M4029.7φ35.8φ28.6φ

BS 8110-1:1997 (UK, still used in Malaysia and elsewhere)

Anchorage length = φ × 0.87 fy / (4 fbu),  fbu = β √fcu  (cl. 3.12.8.3–3.12.8.4)

For type 2 deformed bars, β = 0.50 in tension and 0.63 in compression. The results below match BS 8110 Table 3.27 (for example 37φ for fcu = 30 with fy = 460).

fcu (N/mm²)fy 460, tensionfy 500, tension
2540.0φ43.5φ
3036.5φ39.7φ
3533.8φ36.8φ
4031.6φ34.4φ

Eurocode 2 (EN 1992-1-1)

lb,rqd = (φ / 4) × (σsd / fbd)  (cl. 8.4.3)
fbd = 2.25 η1 η2 fctd  (cl. 8.4.2)
lbd = α1α2α3α4α5 lb,rqd ≥ lb,min

η1 = 1.0 for "good" bond conditions and 0.7 for "poor" (for example, top bars in deep pours); η2 = 1.0 for φ ≤ 32 mm. fctd = fctk,0.05 / 1.5. The table assumes σsd = fyd = 500/1.15 = 435 N/mm² and all α factors = 1.0, which is conservative for straight bars.

Concretefbd (N/mm²)lb,rqd, good bondlb,rqd, poor bond
C20/252.2548.3φ69.0φ
C25/302.7040.3φ57.5φ
C30/373.0036.2φ51.8φ
C35/453.3032.9φ47.1φ
C40/503.7529.0φ41.4φ

The minimum in tension is lb,min = max(0.3 lb,rqd, 10φ, 100 mm). Check your National Annex: the UK Annex keeps αct = 1.0 for bond, as used here.

ACI 318-19 (USA)

The simplified expressions of Table 25.4.2.3 (SI units, clear spacing and cover meeting the table's conditions):

No. 19 (≈ 19 mm) and smaller: ld = fy ψt ψe / (2.1 λ √f′c) × db
No. 22 and larger: ld = fy ψt ψe / (1.7 λ √f′c) × db
ld ≥ 300 mm
f′c (MPa)Grade 420, bars ≤ No. 19Grade 420, bars ≥ No. 22
2143.6 db53.9 db
2837.8 db46.7 db
3533.8 db41.8 db

Values assume uncoated bottom bars in normal-weight concrete (ψt = ψe = λ = 1.0). Top bars with more than 300 mm of fresh concrete below them take ψt = 1.3.

Worked example: 16 mm bar in tension

CodeAssumptionsRatioLength for φ16
IS 456M25, Fe50048.5φ777 mm
BS 8110fcu 30, fy 50039.7φ635 mm
EC2C30/37, good bond, α = 136.2φ580 mm
ACI 31828 MPa, Grade 42037.8db605 mm

The spread looks large, but each code pairs its anchorage rule with its own material factors and detailing rules. Use one code consistently through a design.

Practical points

  • Reduce by the stress actually needed. All four codes let you reduce the length when the bar is not fully stressed (As,req / As,prov), subject to minimums.
  • Bends and hooks help. Standard hooks count towards anchorage, so a bar entering a narrow column can be hooked instead of running straight.
  • Top bars need more. Poor bond (EC2) or ψt = 1.3 (ACI) adds 30–43% for top bars in deep members.

FAQ

Is development length the same as lap length?

No. Lap length is based on development length but is usually longer: EC2 multiplies by α6 (up to 1.5), IS 456 takes the larger of Ld and 30φ, and ACI Class B splices use 1.3 ld.

Why does development length fall as concrete gets stronger?

Bond strength rises with concrete tensile strength, so a shorter length can transfer the same bar force.

What does 40φ mean on a drawing?

40 times the bar diameter. For a 20 mm bar, 40φ = 800 mm.

References

  • IS 456:2000, Plain and reinforced concrete: code of practice, cl. 26.2.
  • BS 8110-1:1997, Structural use of concrete, cl. 3.12.8 and Table 3.27.
  • EN 1992-1-1:2004, Eurocode 2: Design of concrete structures, Section 8.
  • ACI 318-19, Building code requirements for structural concrete, Chapter 25.

Written by Engr. Abdul Latif, civil and structural engineer. Last reviewed: 16 November 2026. Check the code edition and National Annex that apply to your project.