Home / Concrete / Bar Bending Schedule

Bar Bending Schedule

Quick answer: A bar bending schedule (BBS) lists every reinforcement bar in a member with its mark, size, number, shape, cutting length and weight. Cutting length = total of the bent dimensions + hook allowances − bend deductions. Weight = cutting length × D²/162. For the 300 × 450 mm beam worked below, the BBS totals 47.4 kg of steel.
Bar bending schedule worked example: beam elevation and cross-section with 3T16 bottom bars, 2T12 top bars and R8 links

The structural drawing shows where bars go. The bar bending schedule tells the bar bender exactly how long to cut each bar and how to bend it, and tells the quantity surveyor how much steel to buy. This guide explains the formulas, then builds a complete BBS for a simple beam.

What goes in a BBS

ColumnWhat it means
Bar markA unique label (B1, B2, S1…) that matches the drawing
Type and sizeGrade and diameter, e.g. T16 = high-yield 16 mm, R8 = mild steel 8 mm
Number of barsBars per member × number of identical members
ShapeA sketch or a shape code (BS 8666 uses numbered shape codes)
Cutting lengthLength of straight bar needed before bending
Total length and weightNumber × cutting length, then × D²/162 for kg

The three rules behind cutting length

1. Add up the bent dimensions

Measure each straight part of the bar along its outside dimensions, as shown on the bending sketch.

2. Add hook allowances

A hook adds extra length beyond the bend. In common site practice (following IS 2502 and SP 34), a 135° link hook is taken as 10d and a 180° hook as 9d, where d is the bar diameter. Your project specification may state different values; use those if it does.

3. Subtract bend deductions

When a bar is bent, its outside dimensions add up to more than the bar's real length, because the bar wraps around a curve. The usual site deductions are:

Bend angleDeduction
45°1d
90°2d
135°3d
180°4d

These are practical approximations for standard bending formers. Where BS 8666 applies, use its shape-code formulas instead, which already include the bend allowances for the minimum former size.

Worked example: BBS for a simply supported beam

Given: beam 300 mm wide × 450 mm deep, clear span 4,000 mm between two 230 mm supports, cover 25 mm. Bottom bars 3T16 and top bars 2T12, each with a 300 mm leg bent up/down at both ends (90° bends). Links R8 at 150 mm centres with 135° hooks.

Bottom bars (B1, 3T16)

Straight length = 4,000 + 2 × 230 − 2 × 25 = 4,410 mm
Add two legs: + 2 × 300 = 600 mm
Deduct two 90° bends: − 2 × (2 × 16) = 64 mm
Cutting length = 4,946 mm

Top bars (B2, 2T12)

4,410 + 600 − 2 × (2 × 12) = 4,962 mm

Links (S1, R8 at 150 mm)

Link size (outside) = (300 − 2 × 25) × (450 − 2 × 25) = 250 × 400 mm
Perimeter = 2 × (250 + 400) = 1,300 mm
Hooks: + 2 × 10 × 8 = 160 mm
Bends: three 90° (− 3 × 2 × 8 = 48 mm) and two 135° (− 2 × 3 × 8 = 48 mm)
Cutting length = 1,300 + 160 − 96 = 1,364 mm
Number of links = 4,000 / 150 + 1 = 27.7 → 28 links

The finished schedule

MarkBarNo.Cutting length (mm)Total length (m)kg/m (D²/162)Weight (kg)
B1T16 bottom34,94614.841.58023.45
B2T12 top24,9629.920.8898.82
S1R8 links281,36438.190.39515.09
Total47.36 kg

For a floor with 10 identical beams, multiply the "No." column by 10 rather than repeating the rows. See the unit weight of steel bars table for every kg/m value used above.

Tips that save rework on site

  • Check the link count at both ends. Many designs need closer link spacing near supports; the simple "span ÷ spacing + 1" only works for uniform spacing.
  • Add laps for long bars. If a cutting length exceeds the stock length (often 12 m), add a lap and show it in the schedule.
  • Round up, not down. Round cutting lengths up to the nearest 5 or 10 mm, as your bar bender works.
  • Keep marks unique per drawing. Two bars with the same mark but different shapes will be bent wrong.

FAQ

Why do we deduct length at bends?

Dimensions on a bending sketch are measured to the outside of the bar. The bar itself follows the inside curve, so the real length is shorter than the sum of the outside dimensions.

Is the hook length 9d or 10d?

Both are used: 9d is common for 180° hooks on main bars and 10d for 135° link hooks. Always follow the project specification first.

What is a BBS shape code?

BS 8666 gives each common bar shape a number (for example 00 for a straight bar, 21 for a U-bar, 51 for a closed link) with a standard cutting-length formula, so drawings and schedules don't need sketches.

Should the BBS include wastage?

No. The BBS shows exact quantities. Add a wastage allowance only when you turn it into a purchase order.

References

  • BS 8666:2020, Scheduling, dimensioning, cutting and bending of steel reinforcement for concrete.
  • IS 2502:1963, Code of practice for bending and fixing of bars for concrete reinforcement.
  • SP 34:1987, Handbook on concrete reinforcement and detailing (BIS).

Written by Engr. Abdul Latif, civil and structural engineer. Last reviewed: 16 November 2026. Always schedule to the approved drawings and project specification.