Home / Engineering / Beam Deflection Formulas

Beam Deflection Formulas

Quick answer: Maximum deflection of a simply supported beam under a uniform load is δ = 5wL⁴ / (384EI); with a central point load it is PL³ / (48EI). A cantilever deflects wL⁴ / (8EI) under uniform load and PL³ / (3EI) under an end load. The table below gives the maximum moment and deflection for the eight cases engineers use most.

Beam deflection diagrams: simply supported beam with uniform load, 5wL4 over 384EI, and cantilever with end load, PL3 over 3EI



Deflection checks often govern long-span beams, especially in steel and timber. These are the standard elastic formulas for prismatic beams (constant EI), with a worked steel example and the usual limits.

Free calculator: beam deflection, shear force and bending moment

Analyze simply supported, cantilever, fixed-fixed, and propped cantilever beams under arbitrary point loads and distributed loads. Plots high-resolution Shear Force Diagrams (SFD), Bending Moment Diagrams (BMD), and elastic deflection profiles.

Standard cases

Support and loadMax momentMax deflectionWhere
Simply supported, uniform load wwL²/85wL⁴/(384EI)Midspan
Simply supported, central point load PPL/4PL³/(48EI)Midspan
Simply supported, two equal loads P at third pointsPL/323PL³/(648EI)Midspan
Cantilever, uniform load wwL²/2wL⁴/(8EI)Free end
Cantilever, end point load PPLPL³/(3EI)Free end
Fixed both ends, uniform load wwL²/12 (at supports)wL⁴/(384EI)Midspan
Fixed both ends, central point load PPL/8PL³/(192EI)Midspan
Propped cantilever, uniform load wwL²/8 (at fixed end)wL⁴/(185EI)0.42L from the pin

w is load per unit length, P a point load, L the span, E the elastic modulus and I the second moment of area. Keep units consistent: N, mm and N/mm² work well.

Worked example: steel beam, 6 m span

Given: simply supported, L = 6,000 mm, variable (imposed) load w = 10 kN/m = 10 N/mm, E = 210,000 N/mm², I = 95.1 × 10⁶ mm⁴ (the 300 mm deep I-section from our area moment of inertia example).

δ = 5 × 10 × 6,000⁴ / (384 × 210,000 × 95.1 × 10⁶)
= 6.48 × 10¹⁶ / 7.67 × 10¹⁵
= 8.4 mm

Typical limit for imposed-load deflection of a beam carrying a brittle finish is L/360 = 16.7 mm, and L/250 = 24 mm for general use. 8.4 mm passes both. The maximum moment is wL²/8 = 10 × 6²/8 = 45 kNm, which you would check separately for strength.

Combining load cases

For elastic beams, deflections from different loads simply add (superposition). A beam with a uniform load and a central point load deflects 5wL⁴/(384EI) + PL³/(48EI) at midspan.

Typical deflection limits

MemberCommon limitSource
Steel beams carrying plaster or brittle finish (imposed load)span/360UK NA to BS EN 1993-1-1 (guidance)
Other steel beams (imposed load)span/200UK NA to BS EN 1993-1-1 (guidance)
Steel cantileverslength/180UK NA to BS EN 1993-1-1 (guidance)
Concrete beams and slabs (total, appearance)span/250EN 1992-1-1 cl. 7.4.1
Concrete, after finishes are installedspan/500EN 1992-1-1 cl. 7.4.1

Your project specification or client may set tighter limits, for example for glazing or sensitive equipment.

Things that change the answer

  • Concrete cracks and creeps. These formulas give short-term elastic deflection. Reinforced concrete needs cracked-section stiffness and long-term creep; EC2 and ACI give methods, or use span/depth ratios.
  • Shear deformation. Ignored here; it matters only for short, deep beams.
  • Partial fixity. Real connections are neither perfectly pinned nor fully fixed. The pinned case is the safe upper bound.

FAQ

What is EI?

Flexural rigidity: the product of the material's elastic modulus E and the section's second moment of area I. Doubling either halves the deflection.

What is E for steel and concrete?

Structural steel: 210,000 N/mm² (EC3) or 200,000 N/mm² (AISC). Concrete: about 30,000–35,000 N/mm² for C25–C40 (EC2 Table 3.1, Ecm).

Why is a fixed-ended beam five times stiffer?

For a uniform load, 5wL⁴/384 versus wL⁴/384: the end moments reduce the midspan bending, so the curve flattens.

References

  • SCI P363 and the Steel Construction Institute design tables for standard beam formulas.
  • UK National Annex to BS EN 1993-1-1, NA.2.23 (vertical deflection guidance).
  • EN 1992-1-1:2004, cl. 7.4 (deflection control).
  • AISC Steel Construction Manual, Table 3-23 (shears, moments and deflections).

Written by Engr. Abdul Latif, civil and structural engineer. Last reviewed: 16 November 2026.